How to replace the evil taste at the toilet bowl. Vlashtuvannya, vstanovlennya that usunennya possible malfunctions of the evil tank to the toilet bowl. The process of installing a pouring column

Installing sanitary ware in a new booth or a recently purchased apartment, it is necessary to ask about the correct installation of the toilet bowl, the installation of hoses and pipes, the correctness of gaskets and fixing. Old plumbing will also rarely require a preventative inspection. Through the filthy water, the fittings are worn out and go out of tune, and the term repair of the pouring cistern is also required. Calling to stand for the flooding of the dwelling, zokrema and susіdіv from below.

Why is the evil tank built up

From the first glance - the simplest attachment: a capacity, possessed by a system of anger and water supply. When pressing on the button, the mechanism releases water, the supply valve opens, the container is empty and starts up again.

The main functional parts of the tank: 1(1) - inlet (filler) fittings; 1(2) - drain (pour) mechanism; 1(3) – button for activating water. All the details are tied together

Video: how to remove the toilet lid

Do-it-yourself tank repair

It seems to inspire such an elementary attachment, it can be evil. Let's take a look at the report, how you can fix faults without going to the help of plumbers.

Troubleshooting the float mechanism

If water is constantly being collected in the tank and poured into the toilet bowl - look for a problem in the float mechanism. The reasons for the breakdown can be but a kilka:

intake valve wear;
peroxide vazhela ("yoke");
buoy failure.

The float (buoy) in the old exploitation gives cracks, like water in the middle of it. In tone and stop victorious over the main function - replace it next.

As soon as it is important, it is necessary to turn yoga in a correct, horizontal position. Roztashuvannya vazhelya - about 2 cm below the opening, through which water enters.

Modern sets of pouring fittings can be used in the future - until the warehouse does not include a traditional float on the yoke, although the principle of robotic mechanism is saved.

Installed in the tanks of modern toilets, the float mechanism can be divided into pistons and membranes. The first may be the simplest design, in which the piston with the cuff narrows down to the valve seat and in this way interrupts the water supply. Others are recognizable by the new growth - they can be seen in the most important modern wicked cisterns. Instead of a piston with a gasket, a membrane is installed in them made of wear-resistant silicone or latex, which is why it is important to reduce the noise significantly.

The membrane valve of the pouring tank wants and can be foldable design, prote otrimav wide popularity of high reliability and quiet operation.

It doesn't matter if the failure of the mechanism, which is hovering, is most often due to the wear of the strengthening gasket in the first fall and the membrane in the other. In addition, malfunctions of the float valves may be due to malfunctions of other parts of the mechanism:

axis of the managerial value;
saddle;
inveterate cowboy.

If you want to be present at the trade line of inlet fittings, whether of some type or size, and allow you to replace the entire vuzol at the assembly, hurry up with cym not varto. Dbaylivy gospodar obov'yazkovo razbere mekhanіzm and after revealing the cause of the leak usun breakage for the help of handicrafts. So, the gasket can be strengthened by using a natural shkir or a thick gum, all can be replaced with a thicker dart or a flower, and a cap is taken from a wide-ranging strengthening material.

How to get rid of the noise when filling the tank

The booming noise that accompanies the process of filling the tank with water creates discomfort for those who do not feel comfortable. Pozbutis yogo awkwardly, adjusting the diameter of the inlet opening or adding fittings with a small plastic tube. The water ceased voluntarily, pouring noisily into the tank, and coming through the tube, apparently, a booming sound was heard. For this one, a pipe with a length of 30-35 cm is put on the opening with one end, the other is placed lower than the equal water with an empty tank. Now, there is no residual noise, the plumbing is more quiet.

A plastic or gum tube, put on the intake opening, muffles the noise of the water coming into the tank. This attachment is relevant for cisterns from the upper ledge.

Replacing bolts at different leaks

Here, better for everything, the steel bolts rotted, like fastening the tank to the toilet bowl - it is necessary to replace them in terms. Having bought a new set of bolts, we proceed to dismantle the tank:

we turn off the water by turning the valve perpendicularly;
we dry everything in the middle and see the surplus of rusty reinforcement;
screw the nut and open the intake valve;
vіdkruchuєmo old bolts that fix the tank on the toilet bowl;
remove the tank from the gum slit cuff;
let's go old talk. It is necessary to see insults, to bring on just one of them as an injustice;
cleanly place the bolts with the tank and the tank with the toilet bowl;
tighten new bolts;
we install the tank on the floor, fastening the cuff in front;
tighten the fastening carefully, so as not to harm the sanitary ware;
let the water go over, so that it doesn’t blow out in the lower part of the tank; a couple of times we let the water down and once again it is checked.

Sometimes the tekti can show up three times a year, so for two days it’s important to look over the problem area. Yak bachite, don't wait to spend overhaul- Sometimes you need to replace the reinforcement.

For screwing the bolts to put the cistern inside the toilet bowl, a special tool is not needed: ring for manual burying of the head

Fixing for the toilet cistern is supplied in a leather plumbing shop. The price of the found one is 40-50 rubles, the expensive option costs 250-300 rubles

Dumka expert
Viktor Kaploukhy
As if the toilet bowl had been victorious for a trivaly hour, then, better for everything, talk about closing the tank and the bowl of the toilet bowl, rusting the flooring, so that you can’t twist them into the walls of the universal oil WD-40. At this point, it’s more than just a grinder, for help, it’s necessary to carefully look at the bolts from the bottom side of the polka. Best of all, even if you take a tank from your home, you are guaranteed to lose your wine. Pіdshukuyuchi fastening for replacement, choose metalwork from brass. This alloy is highly resistant to corrosion, so if it is necessary to take it apart, you can easily work it.

What work, if the water is constantly flowing

You can’t talk about how to save money, because it’s constantly flowing in a thin stream into the toilet, not allowing the necessary volume to accumulate in the container.

Shvidshe for everything, on the right in the membrane of the siphon, as if she was wearing it, hermetically closed the opening. The problem is eliminated by a simple replacement of the membrane with a new one.

For which next vikonati dekіlka diy:

anger the water;
remove the siphon;
remove the old membrane, install a new one;
place the siphon on the plate, bring it to the bottom, tighten the fixing nut.

On the right side, not in the membrane, but in the broken rod, which can also be easily replaced.

The siphon membrane is located at the lower part of the pouring fittings. Vaughn with a gum gasket, which ensures the safety of the storage of parts

Dumka expert
Viktor Kaploukhy
Zavdyaks of various hoardings I write on various topics, but my favorites are technics, technologies and everyday life.
The constant flow of water from the tank into the toilet is often not associated with any injustice. It seems to be similar in that case, if for some reason the regulation of the overflow has broken down. If the pouring tube is installed correctly, then the rivulet in the tank should be changed 20 mm below the plane of the eye. At the same time, the edge of the pouring channel is to blame for the inlet branch pipe of the inlet hose, which is 10 mm larger and lower.

So robiti, like the evil tank does not look like

Later, inexplicably, the water stopped flowing at the tank. What will be enough for independent repairs, what will it take to get to the plumbing? Let's take a look at three ways of solving the problem.

For the cob, we will check the correctness of the hose, what to supply. We cut off the water, pull the hose out of the tank and place it over any kind of container (possibly over the tank). Trochy turn the valve, I start the water again. As with a hose, everything is safe, water will flow freely from the reservoir. Otherwise, you may have to replace yoga.

It’s possible, when the hose was brought in, what to bring in, so after the repair of the pipeline near the water, the sand and other mechanical zabrudnennya, the buildings are closed, open a little. You can try to clean yoga for the help of a sharp, upholstered object, for example, twists.

In addition, the next step was to change the purity of the coarse filter, as a modern locking fitting with a membrane valve was installed in the tank. For this purpose, you need to get a water supply and, for additional help with thin sponges, pull the filter from the pipe to bring it in. To clean up the yogo in the grove, enough to place the detail under a strong stream of water. If the filter is clogged with stable deposits, then place it on a sprat of a year in an estimate or rozchin citric acid, after which clean with a penzlik from a hard bristle.

The cost of a new hose, what to supply, is close to 100 rubles. It’s better to buy a virib, which can shut off the valve - at the time of the leak of the pouring tank, it’s easier to shut off the water

As if the failure of the float mechanism was due to the wear of the inlet valve, it would be necessary to replace the intake valve at the intake. Vitracheni for the repair of forces that hour does not cost a bet of hundreds of rubles, so that you will have to pay for new fittings. As practice shows, repairing the locking mechanism is given to individuals - better for everything, do not enter until the next day.

Reinforcement replacement

There is no way to mess around with the shreds of fittings that have come into disrepair, you can just see the old one, and install a new one in the same place, near the store mechanism.

Viymayuchi old fittings, to bring respect to the point of failure. It is possible, it is not necessary to replace the mechanism again, for an hour it is enough to remember one detail

Sets of armature for nasty cisterns may have constructive vіdmіnnostі. For example, їх budova vaє differently fallow in the form of water supply - lower bіchnoi chi

For the cob, let's figure it out, as a better way to figure out the design on the butt of the reinforcement with the lower water supply:

we cut off the water;
gently twist the button;
we take the cover;
vіd'єdnuєmo dvedennya;
znimaєmo zlivnu column by parts: on the back of the head, dismantle the upper part (turning 90 degrees);
vіdkruchuєmo fastening of the pouring tank;
put yoga for distant robots on the toilet;
twist two nuts: fastening of the valve and column, distant to another piece of fittings;
we install a new mechanism and a conductive closing robot from the installation of the cistern.

Like bachite, remember the warehouse of the tank is not easy: the whole operation takes no more than 10-15 quills. Another advantage of self-reliant robots is not a need for a special tool, all work is carried out with the help of hands, pliers and keys.

It is impossible to name an apartment, a private house, or a cottage, ordered, as if it were a filthy cistern. What type of plumbing is available in today's stores? But there are no special features of the internal mechanisms of the pouring tank of the toilet bowl with a button.

The principle of work is identical. As a rule, problems were blamed on the water supply to the reservoir, most often the cause was the evil mechanism of the tank. How to solve problems on your own, rozpovimo gave.

In contact with

Yak vlashtovany toilet bowl

Plugging the cistern into the toilet bowl with a button does not strike a special fold. The inside of the cistern, which is used to install the pouring valve for the toilet bowl, is a whole set of basic components:

open for zlivu rіdini, rozmіshcheny under the singing kut;
overflow pipe, installed in the flank part of the drain opening;
a cap for the valve from a narrower look of the horn;
a mechanism that viconizes the function of filling the tank;
Zlivu buttons.

Attachment, which is responsible for the correct filling of the tank with water, is a mechanism for supplying water. Folded wines from the advancing elements:

the presence of a float;
shut-off valve.

The principle of work I will attach a floating float in the step. Before an important mechanism, the preparation of some kind of vicorous metal and plastic, attachments without a middle float. As a result of changing the level of filling of the toilet bowl, the rotting of the float is changing. At the maximum filling capacity, the attachments should be located at the maximum raised position.

Himself in the camp importance is poured into the valves yakі do not allow you to come to the room. As soon as it becomes angry, the float sinks to the minimum level, and the locking mechanism opens, after which the country again without interruption starts flowing into the tank.

The principle of robotic zlivu

Models of the new generation may have a floating drain button. To the thought of fakhivtsiv, such an attachment helps to protect a lot of water that is stained. Reaches all the winds of the noble mechanism of evil:

The standard type of zlivu is to keep an eye on the water from the tank again, as for the norms to become from 4 to 6 liters.
The half type allows you to dispense zliv. At one time you can only anger half the water that is in the tank.. Call for 2-3 liters. This type itself allows you to save water. Ale, for its functionality, wines are more attractive and easy to repair. It was primed because there are more details in the annex. As a result of which, the breakage is expected.

There is one more variant of the power of the noble mechanics. Vіdminnіst polagaє vіdsutnostі button vіdsutnosti zlivu vіnіtіzu, and stіvіnіst zlіvu lie down vіd step vіdskannya on vіlіl. As soon as you press lightly on the important, the water begins to get angry, and as soon as they let in, the mechanism is again twisted. In order to make the tank more angry, it is necessary to press it strongly and all the way.

Adjustable amount of water at the tank

In nasty tanks, you can adjust the coolant that fills the tank. For this function, a knitting needle is used, at the end of which there is a float. Changing її dozhina, you can change the amount of water. In rich models of evil cisterns, the role of an important gray is played by brass drіt. Change її dovzhina awkwardly. If you bend її so that the float appears as a big one, then the number of waters will increase. The lowering of the level of the position of the float is necessary to change the steps of the filling of the container.

In rich brass options, it was important to replace them with plastic ones. In this way, bend yoga and remember in this way the ribs of the float will not go in. Here such an attachment is transferred, like a hairpin, a vzdovzh osi vazela is placed. Ruhayuchi її in one hour's beat, change the shoulder of the important. The farther away from the flank of the toilet bowl the float mechanism will be spread, the more water is needed in the toilet.

In quiet models, which have a lower water supply, the shoulder is placed vertically. In this mode, the adjustment is easy to carry out.

The float mechanism collapses uphill or down, then to be fixed specially by transferring to the hard attachment. Ale all the same deyakі nesruchnosti є. To adjust, lift the reservoir cap.

This procedure is made more complicated by the fact that a button for zlivu is attached to the krishtsi, as if it is directly closed by the release mechanism. When disassembling, it is necessary to check the robot carefully, so as not to damage the entire system

Possibility of breakage of the pouring mechanism is suggested by the fact that wines are mainly composed of parts made of plastic. Ale vtіshaє those that are in stores with free access, i will cover the whole mechanism, so i okremі yogo details.

Important! Repair of the pouring mechanism to lie down in view of the breakdown. In okremikh vypadkah it is possible to replace only a detail, and in the others it is easier to replace the reinforcing bars.

Vlastuvannya and installation of the pouring mechanism

For the supply of water from the evil one, the bowl of the toilet bowl must be given a special mechanism. Consists of the following attachments:

angry siphon;
handles, as if we were pulling the trigger.

The siphon is firmly attached to the evil opening, which does not allow water to pass without consumption. Whose attachment is subdivided into sprat species:

Forgiveness. It is an appendage of a cylindrical shape with a shchelnoy gumi, which is called a pear. The mechanism for lifting the pear is most important, the place of rotting is marked on the side of the tank. In other cases - a handle, ruffled on the krishtsi. To bring її into the day, it is necessary to raise the handle uphill.
The button, which is responsible for the descent of the middle, is mounted on models that are developed for new technologies. Placed on the panel in the foreground. Most often, you can drill on the racks, which are mounted directly against the wall.

After the completion of the installation work at the bathroom, proceed to the installation of the pouring tank, or rather, to the selection of the internal system.

How to pick up a tank? To complete the procedure, it is necessary to follow the following instructions:

On the pouring mechanism, a gum lining is installed.
Drive the mechanism straight into the chamber and screw it behind the additional plastic nut.
On fixed push pucks on plastic or metal. Tse vzhe lie down in addition, as staffing virib. Do not forget about gaskets with gumi. Then the bolts are inserted into the opening, and nuts are mounted from the turning side, having installed them in front.
On the nut made of plastic, they put on a gummed ring for strengthening. In that case, if the vicorist element is new, then come in if it is not necessary to seal the work. In another case, it is necessary to carefully coat the sealing compound with a sealant.

Please! necessary relativly look at all the details with the method of revealed defects. In addition to the areas of sealing, it is necessary to coat them with a sealant. Kіltse ushchіlnyuvacha is also sealed. I will help you a lot with the selection scheme that goes to the dermal sanitary ware.

Prices for the evil mechanism for the toilet bowl

evil mechanism for the toilet bowl

Possible inaccuracies

In that case, if they ran into the installation of fittings and launched it into the robot, it is necessary to take care of them. After a deaky hour, they can blame deaky inaccuracies, which can be easily repaired on their own. Let's take a look at the problems that are caused by the supply of water.

The most common failure is that the water does not come near the tank, otherwise, on the other hand, it does not attach to the supply. The reason for such breakdowns is valve that controls the flow of water, otherwise float without a hitch. Floats for their design float at the sight of empty cylinders or inverted flasks.

The float of the first type of repair is not allowed, they should be replaced again. Sometimes the entire valve needs to be replaced. If you talk about floats near an inverted bottle, then the cause of problems can be the creation of a hole and other containers in a new one. The solution to the problem is to clean the float in the presence of debris that has been disturbed.

In that case, if everything is good with the float, but the water still does not stop coming in, the valve membrane may be worn out as the cause of the breakdown. Most spare parts come with the kit. In the other case, the detail is bought and replaced. For which valve you need to remove the cap and the membrane is worn. A new detail is being installed at the same time. Then we start to curl up again. Do not forget to clean and open, through which water enters the tank.

Buvaє so that the water begins to flow through the overflow. In this season, I will renew respect for the swimmer and win this regulation. Whatever didn’t help, then proceed to re-check the hairpin. In times of need, it is necessary to replace yoga with a new one, or simply for a midday drіt.

Important! In the event of a number of breakdowns, carefully repair the fittings, wear out the part and replace it. Most often, it is necessary to change the mechanism again, as a few details are worn out.

Like a bachimo, attaching to the toilet bowl is not disturbed by folding. The design of the tank includes two working mechanisms. The first one for giving control is equal to the flush at the pouring tank, and the other one is for pouring into the toilet bowl.

Corisne video: installation of the pouring mechanism for the toilet bowl

On this day, there are a few types of models, but the principle of work is very similar in some respects. Maystry means that in all basic types it is necessary to carry out installation, adjustment and repair independently absolutely awkwardly: to understand how to close a toilet bowl, to force a child to grow. You can solve a lot of problems on the job yourself and do not check for plumbing. And if it is possible to go about the current recruitment, which one will be in the wall, then in this way it is more likely to turn up to reach the masters.

The presence of a tiled toilet room is the most important guarantee of a comfortable stay in any apartment or house. In fact, no one can imagine their everyday life without such an accessory, like. Ale chi rich, who knows from us, what a rank of power and how it works the main component -? There are two reasons why these powers are informed: firstly, knowing the features, I will ask you to choose which one to buy, and in another way, I can tell you about the “insideness” of the possession, it is easier to say, as the very part of the mechanism was deformed at the time the unit went out of tune. The axis of what was given to us in detail from the video to see the evil cistern: attachments, principles of operation of fittings, and the visibility of models.

The design of the pouring tank

Standard tank and two mechanisms: bulk; anger that overflow. In old and modern models, the fittings are worn out.

The filling mechanism includes two components:

Valve - regulates the volume of water at the tank: at the same time, it ensures the supply and shutdown. In older models, the valve is vented to the side of the body, and in newer models, it is at the lower part.
Floater - according to the valve positions: lowering floater - vent valve, raising floater - closing valve. The back of the float is functioning in a horizontal position, but in modern models of wines it collapses less in a vertical plane.

The beginnings of the modernization of the design of the tanks, the filling mechanism, having become more effective: in new models of locking fittings, the valves do not cut off the water step by step, but again at the very end of the set, which guarantees the efficiency of supplying water to the tank.

But the most serious and thorough became the mechanism of anger and overflow. In the old cisterns, under the wicked system, a gum pear was small on the vase, as if it hermetically closed the outer opening. It functioned as simply as possible: pull on the lancet or raise it important - and the water starts flowing into the drain. But the current mechanism is a folding reinforcing unit, which includes two main components:

Overflow - protects the tank from overflowing: if the volume exceeds the maximum sign, the motherland begins to go to the toilet bowl.
Zliv - secure without intermediary zlivannya drive when pushing on the descent of the tank.

Porada. For efficient operation and economy of water, it is recommended to remove the pouring tank from two buttons: for full and for private pouring.

The principle of functioning of the tank

Bigger and old, and modern cisterns - the whole construction. The stench is working on the offensive scheme.

Vody Zmiv:

after pressing on the trigger mechanism (button, it’s important) a special thrust is created, when the float stops pressing on the valve and remains open;
the stik at the overflow system closes;
water from the tank is supplied to the toilet bowl for the zmiv.

Zlivu function

Filling the tank with water:

if the water in the tank drops to the minimum mark, the valve closes, the inlet cock opens and the water supply starts;
near the world, the filling of the tank, the locking float rises, and the strum water changes;
if it starts up again, the float closes the inlet valve and the water supply is applied.

Important! In order for the float to function effectively, after installing the tank, it is necessary to adjust and protest: the wrong position of the float can lead to the fact that the reservoir cannot be filled with a sufficient volume of water.

The pressure on the mechanism of the descent provokes the siphon: through a corrugated tube, water enters the bowl of the toilet bowl, waving the zmiv.
After the siphon is empty, the float of the tank drops and the inlet valve opens, through which water begins to flow into the tank.
If the reservoir fills up again, the float drops and the inlet cock closes.

Varieties of evil flasks

Zlivnі priladi can mother pevnі vіdmіnnostі і in design, і in the principles of work, і old-fashioned- To explore them, let's look at the main criteria for classifying tanks.

Criteria #1: type of escapement mechanism. There are two types of descents:

Knopkovy is the most recent solution. Zastosovuєtsya practically in all closed tanks of the new modification. The button can be roztashovuvatisya either on the krishtsi or on the side of the evil attachment.
Pіdvіsny - lanzig chi important. Vykoristovuєtsya is more important in the suspended evil cistern. The trigger mechanism sounds roztashovuetsya sideways to the body of the attachment.

Button trigger mechanism

Criteria number 2: place of residence. Most of the time, the cistern is installed at once from the toilet bowl - such traditional models are added, which allow, if necessary, to install a special outlet pipe from the cistern capacity to the toilet bowl. Another option is a wall-mounted suspended tank - foldable at the vikonann: it is necessary to fasten the attachment on the working surface and carry out additional inlet and outlet pipes. Then the suspended tank plays against the aesthetics plan - it can be masked under the wall niche.

Criteria number 3: material. Modern pouring cisterns are made more importantly in two variations: faience - attach the most intriguing forms and colors, which have gained popularity for the evening of a large day, at an affordable price and high brightness; plastic - cheap models, which are most likely to be built against the wall, which protect them from the outside vents.

Like a bachite, the evil cistern, which is familiar to all, actually appears to be not such a simple accessory. Before you are the main elements of possession, the principles of its functioning noteworthy features different models - tsі vіdomosti will help you і when choosing a tank, і when diagnosing yogo malfunctions, so don't ignore them, if you want, so that nothing will jeopardize your comfort.

How to use a toilet cistern: video

Vlastuvannya toilet bowl: photo

As long as the toilet tank is working correctly, we should take it in proper order. But be it a breakdown of some simple add-on, you can create serious problems. The uninterrupted sound of running water does not let you fall asleep. If you have installed a water liquor, water that constantly leaks from a tank - turn into more payments for cold water. Rizik flood the susіdіv, like lingering under you, tezh high. Fortunately, it's not complicated. Fix the breakdown if you want to localize the problem before the arrival of the plumber, you can skin.

Features of breakdowns and repairs lie in the model of the pouring tank. Ale є th zagalnі all models of mechanisms. Let's take a look at the most common models and the most common problems.

Important! First of all, you will tell whether it is a repair work with an evil cistern, block the water supply through the inlet pipe.

1 type. Water does not come from the tank

The widest reason for this failure is zasmіchennya nayvzhchoy parts of the valve. To solve the problem, let all the water out of the tank and turn the valve at once with the help of a float. You tap a narrow opening, through which you can get water at the tank. Clean yoga with a bare head or a thin dart.

Trochi turn the valve on the inlet pipe wash the excess of smear. When the water flows freely, turn the valve and install the valve with the float back.

2 type. Water flows all the time

Independently of the model, the rainy tank is equipped with a system of accumulation and descent of water. If the water does not fill the tank, it flows into the toilet bowl, or, having filled the tank, overflows over the top, there are problems in one of the storage lines of the system.

Let's look at the problem, if the pear lied a little softly to the wicked lapel. For її vyshennya, it is necessary to tighten a pear, as if you want to - marvel at the video:

Usunennya problems with the pouring tank with a button

If you press the button on the tank, the water will go down into the toilet bowl. After the descent, the water sinks to the bottom. At the same time, the valve, which closes the opening for the supply of water, is also lowered. Water comes near the tank, the float rises step by step, ruhayuchi important. Having risen to a higher height, the floater is important to take position, if the valve closes the opening of the branch pipe.

The cover with one button is lifted in the offensive order:

Turn the stopper ring around the button. Don't emboss too much too much - a piece of good stuff is made from plastic and can be damaged.
Take off the cover and start the repair.

Please! Be more careful, knowing the lid of the tank. If you mess up її, buying a new one will be super important.

If water does not get into the tank, the cause may be one of two problems.

The pouring mechanism with the widest button

As if bolts were roaring, that the saddle of a pear would be trimmed, it was necessary to change them.

Water from the tank flows through the overflow

The way to solve the problem is stale, depending on the reasons for its appearance.

How to fix the float important not to bring the result, turn the integrity of the hairpin, so that it is mitigated. Poshkodzhenu hairpin to replace the middle dart of the same comrade. Steel drіt do not vikoristovyte, vіn pіddaєtsya corozії.
As an opening for a hairpin at a plastic valve, changing the shape from round to oval and moving, remove the valve. Take yoga with you to the store as an eye for expansion and model, buy a new valve and install yoga.

Repair of a pouring tank with two buttons

Tanks with two buttons are vibrated in order to be able to brew two modes of pouring - the same economy. The fittings in such tanks are equipped with a membrane valve for pouring. As you press the button for the economy mode, it is important not to allow the valve cap to drop to the end, and the water is often drained.

Repair of the pouring cistern with the lower water supply

The most common vicorist is the bіchne pіdvedennya vody v zlivny cistern. But the branch pipe, which is washed on the side, does not look aesthetically pleasing. Bazhayuchi attach the tubes, stop the method of lower water supply. This way of correcting, as the area of application simply does not allow the installation of a tank with water supply.

Important! At the bottom, it is important to respectfully reverse the supremacy and tightness of the day. Protіkannya in tsikh mіstsyah - the most widespread problem.

Malfunctions characteristic of tanks from the lower water supply, sprat:

The water supply system has a low pressure, and the water is constantly coming from the tank. This problem is blamed, for example, the installation of a diaphragm valve on the back. If the pressure of the drive in the system is less than 0.05 MPa, the wine is simply not practical. The best way out of the situation would be to replace the diaphragm valve with a stock one;
The reason for faults is blamed on bad water, or on the top of the tank, it can be in the wrong position. Joden s її elementіv is not guilty of sticking the walls of the tank. Carefully look around the mechanism and adjust your position.
Water through the overflow opening comes near the toilet bowl, as it is incorrectly adjusted or the height of the float is broken. Turn the regulation screw and lower the float.

In case of serious breakdowns of the pouring tank, it is necessary to call a plumber. It is possible to change all trigger fittings. And if you want to fix more problems with this simple mechanism, you can do it yourself for the next hour.

Be it a toilet bowl, with a glance of a plumbing possession, a part of the toilet bowl, like a necessary support of the equal water. Accumulated at the annex, the water is vicorated for the zmiv, and when the mechanism is released, the pumping of the zmiva is pumped out and the water is refilled.

Significant part of the current tanks is equipped with a button system. One or two buttons are often characterized by interchangeability without any compromise on performance. How is the vlastovanie nasty cistern of the toilet bowl with the button for two?

The life of any tank is based on the functioning of systems for the collection of water and water. It is dialed by the airflow of the intake system, which regulates the progressive intake. The inlet is independent of the type of evil possession of the same type and it is built up with a float, which allows you to adjust the intensity of filling the system with water.

At the descent process, additional fittings are installed, which allows control of the process. Such a construction is subject to variability. The positions of the exhaust valves allow vikoristovuvaty dvorezimny and emergency zliv.

With one button

I will add a scheme to a toilet bowl with a button, you can use it on this illustration:

Plastic or metal float regulates the process of opening the poppet valve scho spray water into the tank. The volume of water that comes up is controlled by the diaphragm, as it is provided with a special important outbuilding that regulates, for example, a water jet.

Anger is regulated for the help of the siphon, Roztashuvannyam to serve as a central part. To close the siphon to the system, what to bring in, vikoristovuetsya - “sidlo”. At the top of all constructions, a button is fixed.

The standard siphon can be presented with a rose design, which allows to clean the process of cleaning only the upper part and the lower part is simply flushed.

3 two buttons

Invisible elements of the two-button presentation system plug, float cock and pouring fittings. The visible part of the structure includes a cover and a button.

Vashtuvannya pouring tank with two buttons high level of economy. Vitrata water decreases the accountability of the security for the choice of the minimum amount of anger, or more empty obligations.

An illiterate installation provokes the operation of two buttons as if they were one, with the same obligation. Correct insertion mechanism is characterized small zliv on equal 2-4 liters, and on the great zliv stained close to 6-8 liters of water.

Vіdminnіst vіd konstruktsії vіdnії vіdnії vіdnії cistern cistern with one button іnієyu vіdnіє vyklyuchі vіklyuchі vіd pristroї vpuskaє fittings.

On small outbuildings, it is not possible to install such fittings. If you need a replacement, you can vicorate whether the hydrosystem of a double expansion.

The principle of dividing the mechanism of zlivu

The work of this mechanism starts from the onslaught of a button, as it is connected with the internal elements of the zlivu system. Until that moment, the tank is already filled with water to the regulated level and the entire volume is reduced for an additional gum pear. Such material should be allowed to reach a strong fit to the seat. The onslaught of the button calls out the thrust that hits the pear, in view of which an evil opening opens.

After turning the button at the exit position, it is empty again, the pear does not turn back in its place. The world is filled with water, the pear is tightened, lowered and strongly lies on the seat. However, for the full functioning of the pear, a special pipe is important, as it regulates the influence of the natural forces on the entire humic element.

Possibility of winning and short of both options

One-button vents of the hydraulic system are brought to the category. most popular. Automatic double-button mechanisms are less likely to gain popularity.

The hydraulic system of "small zlivu" is undeservedly underestimated. Prote, now see the tanks equipped with a special element. an auger that shakes the water when it falls down intensively and tightly wraps which positively contributes to the cleanliness of the toilet bowl.

For bajannyam it is necessary to add economical one-button pouring tanks, in which the control of the water supply is possible for additional construction "aqua-stop". The economy is swayed by the pressing of a vice: the first pressing is a rage, and the other is a process.

Zmivni cisterns, which function at the gentry's zlivі, allow you to save maybe twenty cubic meters of water on the river, which is clearly indicated on the windows for payment. Schopravda, varto vrakhovuvati, sho modern two-button mechanisms are more expensive, lower classic one-button option Ale all vitrati dosit shvidko pay off.

The main shortfall of two-button versatility is the need for the installation process to complete a series of folding robots of a regulatory-advanced nature, so that independent installation can be completed with a twisted one.

See the main breakdowns

Most of the breakdowns during the operation of toilet bowls are blamed on the process of failures in the functioning of systems for the collection and pouring of water. Spray imbalance Utvorennyu prot_kan of different intensity. Similar problems are eliminated by replacing a few parts of the entire system kit.

The next thing to remember is that the durability of the inlet elements can be deposited without interruption in the light of the characteristics of the water that is coming in. Dosvіdchenі fahivtsі recommend vikonuvati installed filters.

Before minor breakdowns lie faulty buttons. For more vipadkiv, you can use similar problems washing the membrane with the method of removing the smear. Similar manipulations can be brought to the category of simple ones and can easily be conquered independently.

In addition, to the greatest extent of inaccuracies lie:

Impossibility to fill the tank.
All the water that comes in flows through the ziv or overflows through the internal overflow. Such a situation is most often blamed for the insufficiently sharp pear to be angry or even the gum part of the element was carried.
In two-button systems, water can constantly circulate at different times when laying the membrane. What is the most likely cause of problems poshkodzhennya gaskets that seal.
The button for flushing the toilet bowl does not work.
The problem can be explained by the rose of the important mechanism of the pouring tank with the button and the exit of the zipper from the fastening area.

Malfunctions of outbuildings with lower water supply are especially common, which can be zoomed in by such furnishings:

insufficient drive pressure in the minds of the inserted membrane filling valve, which stimulates the constant flow of the inside of the tank;
wrong position of the inlet valve at some element, they stick together with the walls;
not regulated or the position of the float is broken scho calls out the need to drive through the overflow pipe into the toilet bowl.

The most serious breakdowns can not be overcome independently. In particular, it is necessary to change all trigger valve systems. A plumber's own viklik can be saved in the event of serious consequences and, singsongly, save the hour and strength.